setup_timeshock
no way to compare when less than two revisions
Differences
This shows you the differences between two versions of the page.
— | setup_timeshock [2018/08/14 17:18] (current) – created pinupadmin | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Setting up Timeshock Ultra(steam) ====== | ||
+ | |||
+ | ===== ===== | ||
+ | |||
+ | Note: Make sure you have Timeshock in cabinet mode setup before proceeding to installation into PinUp Popper. Cabinet mode can be a little tricky at first until you get used to it if you haven' | ||
+ | |||
+ | \\ | ||
+ | If you have a Virtual DMD you can follow these instructions from Step 3.\\ | ||
+ | If you have everything working and just want to install into popper proceed\\ | ||
+ | to step 4. | ||
+ | |||
+ | Step 1: Download Freezy' | ||
+ | [[https:// | ||
+ | |||
+ | \\ | ||
+ | Step 2: Extract the contents of dmdext 1.7.1 x64 into your ProPinball Timeshock Ultra folder ex: C:\Program Files (x86)\Steam\steamapps\common\ Pro Pinball Ultra. All those dmdext files aren't used but I went ahead and extracted them to the directory anyway. | ||
+ | |||
+ | Note: you may have a different setup then mine and need to install it into a different directory as long as its in the Pro Pinball Ultra folder. | ||
+ | |||
+ | Step 3: Now we need to go into Steam:\\ | ||
+ | Load up steam and click on your games library, from that library right click on ProPinball Ultra, click on properties. A box will popup with 4 tabs. Under the general tab you should see a clickable "Set Launch Options" | ||
+ | We are going to direct Timeshock how to load up your pindmdv3.\\ | ||
+ | Type in: m3 dProPinballSlave q | ||
+ | |||
+ | Note: If are using 2 sound cards one for Music and Callouts and one for Mechanical Sounds add this to your " | ||
+ | sb0=default sound card\\ | ||
+ | sb1=secondary sound card (you may need to flip flop these\\ | ||
+ | depending on your setup) | ||
+ | |||
+ | Note: m3= 3 monitors and even though you may have a two monitor setup(playfield and backglass)this is the only version I could get to work correctly for my setup of 2 monitors and a real dmd.\\ | ||
+ | Also if you are following this and use a virtualdmd you can follow step 3 but only put "m3 q" or "m2 q" into "Set Launch Otions" | ||
+ | |||
+ | When you have completed this step fire up timeshock and make sure your dmd is\\ | ||
+ | working with it now. | ||
+ | |||
+ | Moving on to installation into PinUp Popper: | ||
+ | |||
+ | Step 4: Navigate to your PinUp System Directory ex: C: | ||
+ | Click the blue next ">" | ||
+ | |||
+ | Note: you can create a new emulator by clicking the " | ||
+ | I chose to use PC Games cause it was halfway setup. | ||
+ | |||
+ | Under the " | ||
+ | |||
+ | You then need to change the " | ||
+ | |||
+ | Tick the box " | ||
+ | |||
+ | Dont close out the emulator setup box youll need it for step 5. | ||
+ | |||
+ | Step 5: Click on the " | ||
+ | |||
+ | Note: If you setup a new emulator instead of using the default PC emulator the " | ||
+ | box will be empty | ||
+ | |||
+ | In the blank " | ||
+ | |||
+ | < | ||
+ | @echo off | ||
+ | |||
+ | START "" | ||
+ | START "" | ||
+ | </ | ||
+ | |||
+ | Popper Close Script | ||
+ | |||
+ | < | ||
+ | " | ||
+ | </ | ||
+ | |||
+ | Note: If you created a new emulator add the default "Close Script" | ||
+ | |||
+ | < | ||
+ | " | ||
+ | </ | ||
+ | |||
+ | Step 6: Click the green checkmark at the bottom of the page to save your changes and close out the emulator setup. Make sure you add the game to your system in the games manager and also put it in your playlist. Let me know how it works out for you. Enjoy! | ||
+ | |||
setup_timeshock.txt · Last modified: 2018/08/14 17:18 by pinupadmin